Weld and Go
More Output for Managers. Less Fatigue for Welders. Same Machine.
SWAP TIG/MIG FOR THEO.
TIG, MIG and THEO Laser Welding compared
Why THEO Laser Welding Machines are Worth the Value
| What it means in the shop | TIG | MIG | Laser welding: THEO |
|---|---|---|---|
| Speed on 1–4 mm stainless | Slow, high skill | Fast, spatter | Fastest. One pass and done |
| Heat input and distortion | High | High | Low. Thin sheet stays flat |
| Finish after welding | Clean, but slow | Grinding and cleanup | Bright, narrow bead. Usually no post-processing |
| Training a competent welder | At least 6 months | About 3–6 months | One week |
| Materials | Most | Most | Stainless, mild, galvanised, aluminium, nickel alloys, titanium |
| Cooling and setup | Water-cooled; torch and tungsten electrode, argon shielding gas; foot pedal or thumb control; ground clamp; filler rod | Air-cooled or water-cooled; wire feeder, MIG gun and contact tip; shielding gas; ground clamp; wire spool | Air-cooled; shielding gas; light-weight welding torch; laser safety enclosure |
| Energy consumption | High | High | Lower. Up to 80% less energy |
| What it means in the shop | Laser welding: THEO | TIG | MIG |
|---|---|---|---|
| Speed on 1–4 mm stainless | Fastest. One pass and done | Slow, high skill | Fast, spatter |
| Heat input and distortion | Low. Thin sheet stays flat | High | High |
| Finish after welding | Bright, narrow bead. Usually no post-processing | Clean, but slow | Grinding and cleanup |
| Training a competent welder | One week | At least 6 months | About 3–6 months |
| Materials | Stainless, mild, galvanised, aluminium, nickel alloys, titanium | Most | Most |
| Cooling and setup | Air-cooled; shielding gas; light-weight welding torch; laser safety enclosure | Water-cooled; torch and tungsten electrode, argon shielding gas; foot pedal or thumb control; ground clamp; filler rod | Air-cooled or water-cooled; wire feeder, MIG gun and contact tip; shielding gas; ground clamp; wire spool |
| Energy consumption | Lower. Up to 80% less energy | High | High |
Swipe sideways for TIG and MIG →
Same joint — different speed and precision
Laser Welding outperforms TIG
Ready for your MA1?
Reviews
MANY HAVE SWITCHED TO THEO. YOU?
“These are awesome machines with awesome results. You can get any other machine on the market, and it will not weld as good as a THEO.”
Tyson NelsonOwner, Fine Iron LLC, USA
“The MA1 are the most powerful and yet the smallest laser welding machines on the market.”
Michał PuchcińskiProduct Specialist, RYWAL-RHC Sp. z o.o., Poland

“The operating system is quite simple and much easier to program than other laser welders. So it’s easier for a welder to switch from TIG/MIG to THEO than from TIG/MIG to another laser welding brand.”
Andy González LópezDirector of Operations, CADITEC S.L.U, Spain

“The laser torch is very light, ergonomic to weld with. You can hold it for a whole day without feeling any fatigue in your wrist.”
Benjamin GaytantOwner, BGA Laser Welding, Belgium
Which MA1 is the right model for you?
Let the thickest material you weld guide your choice.
MA1‑35
3.5 mm max penetration (stainless)
800 W laser output · 28 kg
Best for: Thin-gauge stainless, sheet-metal and mobile work; the lightest entry into laser welding
MA1‑45
4.5 mm max penetration (stainless)
1,200 W laser output · 39 kg
Best for: General fabrication up to 4.5 mm with headroom on stainless and aluminium
MA1‑65
6.5 mm max penetration (stainless)
1,500 W laser output · 39 kg
Best for: Most UK fab shops: stainless and mild steel to 6.5 mm, replaces a TIG station
MA1 ULTRA
8.5 mm max penetration (stainless)
2,000 W laser output · 39 kg
Best for: Heavy sections, structural and high duty-cycle production — the deepest handheld weld in the range
All four share the same light-weight ergonomic torch, touchscreen and Maxphotonics air-cooled fibre core.
AVOID FORMAL MISTAKES
LASER SAFETY, AND THE UK REGULATION
The MA1 Series is a Class 4 laser product. As such it requires special attention and compliance with the current regulations.
- Built-in hardware safety. The machines are engineered with safeguards (helmet and door switch interlock) that instantly shuts off the beam if the torch disconnects from the workpiece.
- Define the laser danger zone. Full certified enclosure, fume extraction and appropriate PPE (jacket, gloves, helmet, goggles) are required to weld in total confidence.
- Prevent sanctions. In the UK BS EN 60825-1 is the key safety standard for laser products. Check it out to make sure the environment where the laser will operate is compliant and the welders safe. If an HSE inspector visits a workshop where a Class 4 laser is operated, they will expect the employer to have implemented risk assessments and engineering controls aligned with the national regulation.
UK SALES, SERVICE AND SUPPORT BY

THEO MA1 FAQ
What materials can the MA1 Handheld Laser Welding System weld?
The MA1 series can weld a variety of materials including carbon steel, stainless steel, aluminium, non-ferrous metals, and other alloys. For detailed information on materials and supported welding depths, please download our product brochure.
What should I consider regarding safety?
While the ideal scenario for operating the MA1 series is in a separate room, necessary safety can also be achieved with the use of laser safety curtains. Appropriate laser safety glasses are needed to protect the operator’s eyes during the welding process. We also recommend the use of gloves, long sleeves, and appropriate work boots for additional protection. In some countries, including Germany, a designated laser safety officer is required within the company to ensure all safety protocols are being followed. Safety regulations can vary by region. Our solution expert partners are well-versed in local safety requirements and are more than happy to guide you through the safety protocols applicable in your specific region, ensuring your operations are both safe and compliant.
What certifications does the MA1 series hold?
The MA1 series holds several certifications including EN 60204-1, EN 60825-1, ISO 11553-2, ISO 12100, EN IEC 61000-6-2, and EN IEC 61000-6-4.
What maintenance is required for the MA1 Handheld Laser Welding System?
The MA1 series requires low maintenance, thanks to its air-cooled design which eliminates the need for frequent upkeep and reduces downtime.
What warranty comes with the MA1?
Two years on machine, torch and laser source when you register (one year unregistered). Protective lenses and nozzles are consumables.
How does the demo work?
Bring your own parts. You weld your material on a demo unit — at your workshop, online, or at a Wilkinson Star dealer near your postcode.
Who installs the machine and trains our welders?
Wilkinson Star or your local dealer commissions the machine and trains your welders on site. Spares and consumables come from UK stock.
Let’s get you started
Book your UK demo
Three questions about your work, and a THEO engineer calls you back within one working day with a price ex VAT and a demo date.
Rather talk now? +44 20 8142 9895 (Mon–Fri 8–5)
Your contact details
Takes about 2 minutes. Fields marked * are required.
A real person replies within one working day.
We use your details to answer your request — nothing else. Privacy Policy