Opens in a new tab

US sales & service by THEO

Book a US demo

Handheld laser welding up to 8.5 mm (0.33 in)

America’s go‑to handheld laser welder. THEO MA1

Up to 10× faster than TIG on stainless
Four models from 3.5 mm to 8.5 mm penetration in stainless
Up to 8.5 mm (0.33 in) with the MA1 ULTRA
Prices from $7,480 (+ sales tax)

CEIEC 60825‑1Class 4 laser productA screened bay, laser-safety glasses and fume extraction are part of every install — your dealer sets it up with you.

The MA1 Advantages

TIG, MIG and THEO Laser Welding Compared

What it means in the shop TIG MIG Laser welding: THEO
Speed on 1–4 mm stainless Slow, high skill Fast, spatter Fastest. One pass and done
Heat input and distortion High High Low. Thin sheet stays flat
Finish after welding Clean, but slow Grinding and cleanup Bright, narrow bead. Usually no post-processing
Training a competent welder At least 6 months About 3–6 months One week
Materials Most Most Stainless, mild, galvanized, aluminum, nickel alloys, titanium
Cooling and setup Water-cooled; torch and tungsten electrode, argon shielding gas; foot pedal or thumb control; ground clamp; filler rod Air-cooled or water-cooled; wire feeder, MIG gun and contact tip; shielding gas; ground clamp; wire spool Air-cooled; shielding gas; light-weight welding torch; laser safety enclosure
Energy consumption High High Lower. Up to 80% less energy
What it means in the shop Laser welding: THEO TIG MIG
Speed on 1–4 mm stainless Fastest. One pass and done Slow, high skill Fast, spatter
Heat input and distortion Low. Thin sheet stays flat High High
Finish after welding Bright, narrow bead. Usually no post-processing Clean, but slow Grinding and cleanup
Training a competent welder One week At least 6 months About 3–6 months
Materials Stainless, mild, galvanized, aluminum, nickel alloys, titanium Most Most
Cooling and setup Air-cooled; shielding gas; light-weight welding torch; laser safety enclosure Water-cooled; torch and tungsten electrode, argon shielding gas; foot pedal or thumb control; ground clamp; filler rod Air-cooled or water-cooled; wire feeder, MIG gun and contact tip; shielding gas; ground clamp; wire spool
Energy consumption Lower. Up to 80% less energy High High

Swipe sideways for TIG and MIG →

Laser Welding is Faster than TIG

The Weld Off

TIG vs THEO on the same joint — watch the film.

The Weld Off — TIG versus THEO

Which MA1 is right for your work?

Four models. Pick by the thickest material you weld.

All four share the same torch, touchscreen and air-cooled fiber laser source from Maxphotonics. They differ in laser output, and therefore in how deep they weld in one pass — up to 8.5 mm in stainless with the ULTRA.

THEO MA1‑35

MA1‑35

3.5 mm (0.14 in) max penetration (stainless)

800W laser output · 29 kg

Best for: Thin-gauge stainless, sheet-metal and mobile work; the lightest entry into laser welding

from $7,480+ sales tax

Get a quote
THEO MA1‑45

MA1‑45

4.5 mm (0.18 in) max penetration (stainless)

1200W laser output · 38 kg

Best for: General fabrication up to 4.5 mm with headroom on stainless and aluminum

from $11,980+ sales tax

Get a quote
THEO MA1‑65

MA1‑65

6.5 mm (0.26 in) max penetration (stainless)

1500W laser output · 39 kg

Best for: Most US fab shops: stainless and mild steel to 6.5 mm, replaces a TIG station

from $19,980+ sales tax

Get a quote
THEO MA1 ULTRA

MA1 ULTRA

8.5 mm (0.33 in) max penetration (stainless)

2000W laser output · 42 kg

Best for: Heavy sections, structural and high duty-cycle production — the deepest handheld weld in the range

from $28,900+ sales tax

Get a quote

Rule of thumb: pick the model by the thickest material you weld regularly — 3.5 / 4.5 / 6.5 / 8.5 mm in stainless. Not sure? The MA1‑65 covers most US fab shops and replaces a TIG station.

Ready for your MA1?

Weld your own parts on a demo unit — at your workshop or online.

Reviews

What they say about the THEO MA1

“These are awesome machines with awesome results. You can get any other machine on the market, and it will not weld as good as a THEO.”

Tyson NelsonOwner, Fine Iron LLC, USA

“The quality of the welding seams: my clients are ecstatic when they see the MA1 in action.”

Michał PuchcińskiProduct Specialist, RYWAL-RHC Sp. z o.o., Poland

“The operating system is quite simple and much easier to program than other laser welders. So it’s easier for a welder to switch from TIG/MIG to THEO than from TIG/MIG to another laser welding brand.”

Andy González LópezDirector of Operations, CADITEC S.L.U, Spain

“The laser torch is very light, ergonomic to weld with. You can hold it for a whole day without feeling any fatigue in your wrist.”

Benjamin GaytantOwner, BGA Laser Welding, Belgium

Before you book

Will it work in my workshop?

The three things every fabricator asks before the demo — answered up front.

PowerSingle-phase 220 V. The MA1‑35 runs on a 16 A supply, the MA1‑45, ‑65 and ULTRA on 32 A. No three-phase, no chiller.
SafetyClass 4 laser: you need a screened bay or laser curtains, laser-safety glasses and fume extraction. Your dealer checks the setup at commissioning.
Learning curveA new skill, not no skill. Experienced TIG or MIG welders lay acceptable beads within hours and are proficient in about a week; weld recipes per material and thickness do the parameter work.

THEO MA1 FAQ

What materials can the MA1 Handheld Laser Welding System weld?

The MA1 series can weld a variety of materials including carbon steel, stainless steel, aluminum, non-ferrous metals, and other alloys. For detailed information on materials and supported welding depths, please download our product brochure.

What should I consider regarding safety?

While the ideal scenario for operating the MA1 series is in a separate room, necessary safety can also be achieved with the use of laser safety curtains. Appropriate laser safety glasses are needed to protect the operator’s eyes during the welding process. We also recommend the use of gloves, long sleeves, and appropriate work boots for additional protection. In some countries, including Germany, a designated laser safety officer is required within the company to ensure all safety protocols are being followed. Safety regulations can vary by region. Our solution expert partners are well-versed in local safety requirements and are more than happy to guide you through the safety protocols applicable in your specific region, ensuring your operations are both safe and compliant.

What certifications does the MA1 series hold?

The MA1 series holds several certifications including EN 60204-1, EN 60825-1, ISO 11553-2, ISO 12100, EN IEC 61000-6-2, and EN IEC 61000-6-4.

What maintenance is required for the MA1 Handheld Laser Welding System?

The MA1 series requires low maintenance, thanks to its air-cooled design which eliminates the need for frequent upkeep and reduces downtime.

What warranty comes with the MA1?

Two years on machine, torch and laser source when you register (one year unregistered). Protective lenses and nozzles are consumables.

How does the demo work?

Bring your own parts. You weld your material on a demo unit — at your workshop, online, or at a dealer near your ZIP code.

Who installs the machine and trains our welders?

THEO or your local dealer commissions the machine and trains your welders on site. Spares and consumables come from US stock.

Let’s get you started

Book your US demo

Three questions about your work, and a THEO engineer calls you back within one business day with a price plus sales tax and a demo date.

Rather talk now? +1 (508) 299-5640 (Mon–Fri 9–5 ET)

Your contact details

Takes about 2 minutes. Fields marked * are required.

A real person replies within one business day.

We use your details to answer your request — nothing else. Privacy Policy

Your contact details

Takes about 2 minutes. Fields marked * are required.

A real person replies within one business day.