{"id":16142,"date":"2026-04-28T13:27:23","date_gmt":"2026-04-28T13:27:23","guid":{"rendered":"https:\/\/theo.inc\/?post_type=docs&#038;p=16142"},"modified":"2026-11-17T16:01:02","modified_gmt":"2026-11-17T16:01:02","password":"","slug":"ma1-tutorial-unboxing-and-setup-eu","status":"publish","type":"docs","link":"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-unboxing-and-setup-eu\/","title":{"rendered":"Tutorial THEO MA1 Series (UE) | Despachetare \u0219i punere \u00een func\u021biune"},"content":{"rendered":"<div class=\"video-tutorial\"><div style=\"position:relative;padding-top:56.25%;margin:1.5em 0;\"><iframe src=\"https:\/\/player.mediadelivery.net\/embed\/647770\/0754d718-ec13-49c3-a096-4dd4a284d8a3?autoplay=false&#038;loop=false&#038;muted=false&#038;preload=true&#038;responsive=true\" loading=\"lazy\" style=\"border:0;position:absolute;top:0;height:100%;width:100%;\" allow=\"accelerometer;gyroscope;autoplay;encrypted-media;picture-in-picture;\" allowfullscreen=\"true\"><\/iframe><\/div><\/div>\n\n\n<p class=\"wp-block-paragraph\">This video unboxes a THEO MA1-45 handheld laser welder and the THEO T1 Wire Feeder in Europe and sets both up step by step: what is in the box, power and first start, activation, shielding gas, the interlock circuit with a door switch and the THEO laser welding helmet, the workpiece clamp, the welding torch, the wire spool and the wire liner. At the end, the system is ready to weld.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"in-the-box\">What is in the box<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Lift off the carton. The accessories sit on top of the machine:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n\n<li>The packing list and the operator manual. Check the packing list to make sure everything has arrived.<\/li>\n\n\n<li>The consumables kit: welding nozzles for the different welding styles and wire feed nozzles for all common wire diameters.<\/li>\n\n\n<li>The wire feed bracket, with a small tool to mount it on the welding torch.<\/li>\n\n\n<li>Two pairs of laser safety glasses. They are mandatory for laser-safe operation.<\/li>\n\n\n<li>Spare protective windows.<\/li>\n\n\n<li>The torch holder, which gives the welding torch a safe parking position at your workstation.<\/li>\n\n\n<li>The machine key, a tool for the focus tube and cleaning tools for the protective windows.<\/li>\n\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The welding torch sits in foam for transport. Lift the foam and the carton aside and put the MA1 on a table with a second person, as it is too heavy for one. Under the machine you find:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n\n<li>The gas tubing.<\/li>\n\n\n<li>The workpiece clamp and its cable, which make sure there is a connection between the welding torch and the material.<\/li>\n\n\n<li>A grounding cable, to connect the machine to the ground of your building.<\/li>\n\n\n<li>The DB25 cable for the interlock and other safety connections.<\/li>\n\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"power\">Power and first start<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The machine arrives with a CEE 230 V single-phase plug. Before you plug it in, make sure your electrical installation meets the machine&#8217;s requirements.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Plug the MA1 into the socket.<\/li>\n\n\n<li>Switch on the red main switch on the back. The screen boots.<\/li>\n\n\n<li>Lock the wheels so the machine stands safely.<\/li>\n\n\n<li>Read every safety notice carefully and press Next. They hold important information. At the end, accept the terms.<\/li>\n\n\n<li>Insert the key and turn it to 1 to unlock the machine.<\/li>\n\n<\/ol>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"activation\">Activate the machine<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If the screen says the license has expired, open System Information, tap the Authorization Code box and enter the code from your distributor. The expiry date changes to 2099, which means the machine is fully activated.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"warnings\">Check the warnings<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A blinking red LED and a beep mean the hardware is not set up yet. Open Expert Mode and the Warnings tab. A new machine shows two red symbols: Gas and Interlock alarm. Connecting the gas supply and the interlock circuit clears both, so the machine runs without warnings.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"shielding-gas\">Connect the shielding gas<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The gas tubing has two ends. The blue tube connects to the MA1. The transparent tube with the stainless steel connector goes to your external gas regulator. Use a regulator with a flow meter: it controls the flow rate, not just the pressure.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Most regulators come with a small pack holding a threaded gas connector. Press it over the transparent tube, screw it onto the regulator and tighten it.<\/li>\n\n\n<li>Remove the black cap from the gas inlet on the back of the MA1.<\/li>\n\n\n<li>Push the blue tube in until you feel it click.<\/li>\n\n\n<li>Open the gas supply. The gas warning disappears. The video shows 330 kPa.<\/li>\n\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">Flow rate and gas purity are in the <a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-get-ready-for-delivery\/\">Get Ready for Delivery<\/a> guide.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"interlock\">Wire the interlock circuit<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The interlock alarm clears once your external safety devices are connected through the DB25 port. As with any electrical work, switch the machine off first. Plug in the DB25 cable and tighten its screws.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The video connects two safety devices, one on each of the two interlock channels:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n\n<li><strong>A door switch<\/strong> on the enclosure, so the laser only fires when the door is closed. The wiring depends on the switch your enclosure supplier provides.<\/li>\n\n\n<li><strong>The THEO laser welding helmet<\/strong>, which has its own interlock and comes with a connection plug.<\/li>\n\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The full wiring plan is in the operator manual, including connections for automation and for cabinet options such as LED panels. With both devices connected, the laser only fires when the work area and your personal protection are safe.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Switch the machine on again and check the Warnings tab. With the gas on, the door closed and the helmet on and closed, the interlock alarm goes off.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"workpiece-clamp\">Connect the workpiece clamp<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Plug the workpiece clamp cable into the front panel and clamp the other end to a metal plate or to the base plate of your welding table. When the welding torch touches the workpiece, the safety loop closes. Only with the loop closed and all safety features in place can you weld.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"torch\">Set up the welding torch<\/h2>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Screw on a welding nozzle by hand. The video uses welding nozzle B, marked with a B on top. It is the most common one and covers many jobs.<\/li>\n\n\n<li>Center the focus tube on the torch and tighten it by hand. The setting depends on the job: negative for deeper penetration and thicker material, around zero for thinner material. The video sets minus two to minus three.<\/li>\n\n\n<li>Slide the wire feed bracket over the focus tube with the wire feed nozzle that matches your wire. The size is engraved on the side: for 1.0 mm wire, use the nozzle marked 1.0. Tighten by hand.<\/li>\n\n\n<li>Set the wire distance and angle. Leave 2 to 3 mm between the notch of the welding nozzle and the wire tip, center the wire, and make sure the wire is not under too much tension where it comes out. Tighten with the tool.<\/li>\n\n\n<li>Check again that everything is centered, then put the torch back in its holder.<\/li>\n\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">How the material changes the defocus setting is in <a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-setting-proper-defocus\/\">Setting Proper Defocus<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"wire-feeder\">Unbox and connect the T1 Wire Feeder<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Move the MA1 aside, lock its wheels again and make space for the THEO T1 Wire Feeder next to it. The T1 box holds the packing list, the wire feeder, the wire liner, drive rolls for all common wires and the key for the side panel.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Switch off the MA1.<\/li>\n\n\n<li>Plug the cable with the red dot into the Feeder socket on the back panel of the MA1, red dot to red dot, until it clicks. This one cable carries both communication and power.<\/li>\n\n\n<li>Switch the MA1 back on and wait until it has booted.<\/li>\n\n\n<li>Press the power button on the T1. It lights up red when the T1 is on.<\/li>\n\n<\/ol>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"wire-spool\">Load the wire spool<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Unscrew the spool holder. The adapter takes smaller spools such as 5 kg; without the adapter, the holder takes a 15 kg spool. Fit the spool so its small notch sits in the wire guide, then close the holder.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Release the tension arms and check that the drive rolls match your wire. Note that the drive roll nut has a left-hand thread. The size is printed on the front of each drive roll, for example 1.0 for 1 mm wire. V-groove drive rolls are for stainless steel and mild steel wire.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Cut the end of the wire off cleanly.<\/li>\n\n\n<li>Push it through the guides, from one hole to the next, until the end comes out.<\/li>\n\n\n<li>Close the tension arms and check the tension.<\/li>\n\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">A tension of 3 works for most applications, and the usual range is 2 to 3. Go below 3 for softer wire or larger diameters, and a little above 3 for small diameters and hard wire.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"wire-liner\">Feed the wire to the torch<\/h2>\n\n\n\n<ol class=\"wp-block-list\">\n\n<li>Plug the wire liner into the quick connector and hold the other end without kinking it.<\/li>\n\n\n<li>Press the forward button. If you hold it for more than two seconds, it keeps feeding. Open the door to check that the wire runs smoothly.<\/li>\n\n\n<li>When the wire comes out of the liner, press the forward button again to stop.<\/li>\n\n\n<li>Push the wire through the torch, click the liner into the quick connector and hang it in the hook.<\/li>\n\n\n<li>Cut the wire where the red dot of the guide beam falls.<\/li>\n\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">The MA1 and the T1 are now connected and the system is ready for welding.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"more-tutorials\">More THEO MA1 Series tutorials<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n\n<li><a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-unboxing-and-setup-us\/\">Unboxing and Setup (US)<\/a><\/li>\n\n\n<li><a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-setting-proper-defocus\/\">Setting Proper Defocus<\/a><\/li>\n\n\n<li><a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-proper-wire-alignment\/\">Proper Wire Alignment<\/a><\/li>\n\n\n<li><a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-tutorial-accessories-us\/\">Accessories (US)<\/a><\/li>\n\n\n<li><a href=\"https:\/\/theo.inc\/ro\/knowledge-base\/ma1-get-ready-for-delivery\/\">Get Ready for Delivery (guide)<\/a><\/li>\n\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Questions about your machine? Get support in the <a href=\"https:\/\/theo.inc\/toolbox-app\/\">THEO Toolbox app<\/a> for iOS and Android.<\/p>","protected":false},"excerpt":{"rendered":"<p>Unboxing and setup of the THEO MA1 Series, EU version: activation, gas, interlock and loop cable, welding head, then the wire feeder.<\/p>","protected":false},"author":651,"featured_media":17456,"comment_status":"open","ping_status":"closed","template":"","meta":{"_acf_changed":false,"content-type":"","footnotes":""},"doc_category":[127,396],"doc_tag":[227,226,228],"doc_product":[403],"class_list":["post-16142","docs","type-docs","status-publish","has-post-thumbnail","hentry","doc_category-theo-ma1-knowledge","doc_category-tutorials","doc_tag-laser-welding","doc_tag-ma1-series","doc_tag-video-tutorial"],"acf":[],"year_month":"2026-11","word_count":1374,"total_views":"42","reactions":{"happy":"0","normal":"0","sad":"0"},"author_info":{"name":"Anthony Tabor","author_nicename":"anthony-tabor","author_url":"https:\/\/theo.inc\/ro\/blog\/author\/9d9c305310357cc9ce3256d88c34248b\/"},"doc_category_info":[{"term_name":"THEO Knowledge Base","term_url":"https:\/\/theo.inc\/ro\/manuals-category\/theo-ma1-knowledge\/"},{"term_name":"Tutorials","term_url":"https:\/\/theo.inc\/ro\/manuals-category\/tutorials\/"}],"doc_tag_info":[{"term_name":"Laser Welding","term_url":"https:\/\/theo.inc\/ro\/manuals-tag\/laser-welding\/"},{"term_name":"MA1 Series","term_url":"https:\/\/theo.inc\/ro\/manuals-tag\/ma1-series\/"},{"term_name":"Video Tutorial","term_url":"https:\/\/theo.inc\/ro\/manuals-tag\/video-tutorial\/"}],"_links":{"self":[{"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/docs\/16142","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/docs"}],"about":[{"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/types\/docs"}],"author":[{"embeddable":true,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/users\/651"}],"replies":[{"embeddable":true,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/comments?post=16142"}],"version-history":[{"count":1,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/docs\/16142\/revisions"}],"predecessor-version":[{"id":17486,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/docs\/16142\/revisions\/17486"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/media\/17456"}],"wp:attachment":[{"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/media?parent=16142"}],"wp:term":[{"taxonomy":"doc_category","embeddable":true,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/doc_category?post=16142"},{"taxonomy":"doc_tag","embeddable":true,"href":"https:\/\/theo.inc\/ro\/wp-json\/wp\/v2\/doc_tag?post=16142"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}