Otvara se u novoj kartici
THEO baza znanja · Upute

THEO MA1 Series Tutorial | MA1-65 UI Walkthrough

This video walks through the touchscreen interface of the THEO MA1-65 handheld laser welder. The MA1-35 and MA1-45 use the same interface. It covers basic and expert mode, the details tab, tacking with shooting mode, pulse settings, wire feed settings, status and warnings, saved parameters and the system pages.

Basic mode

Once the machine is activated, it starts with the precautions screen. Press Agree to reach basic mode, which has:

  • Material: stainless, carbon, galvanized or aluminum.
  • Thickness range of the base material. The range changes with the material’s reflectivity.
  • Welding method, your joint fit-up.
  • Funkcija wire feed quick toggle.
  • Funkcija fish scale toggle, to use pulse settings by default.
  • Laser enable, with a warning that the laser is now active and your PPE must be on.

Expert mode: the big three

  • Wobble width: 0.1 to 4.0 mm on the MA1-35, MA1-45 and MA1-65.
  • Laser power in percent. Every model has a minimum of 10% of its power. If you run more than one model, note which machine you recorded a parameter set on, so you do not have to convert later.
  • Wobble frequency: how many times per second the wobble moves back and forth across the joint. You can slow it way down or speed it up; it goes above 300, but there is no real reason to use that.

Expert mode also has the wire feed toggle and the gas manual button, which purges the gas line.

Details tab

The details tab shows the same big three plus these settings:

  • Gas on delay is the pre-flow. The video sets one second.
  • Gas off delay is the post-flow, set in milliseconds. The video sets half a second.
  • Light off delay gives you a little more time to break the wire. The torch still needs contact with the workpiece. The video sets an eighth of a second.
  • Ramp up raises the laser power from 10% to the power you set. Ramp down lowers it back to 10% before the laser switches off.

Shooting mode for tacking

Shooting mode is the MA1’s answer for tacking. Shooting time is the laser-on time; the video uses 400 ms. Shooting interval is the time between laser-on times, so you can plan your travel and your approach from one tack to the next.

Pulse settings and wire feed

The pulse settings have the same big three plus gas on and gas off. Laser frequency is how many times per second the process beam is pulsed. Duty cycle, in percent, matches the power delivery to the deposition and penetration you want.

When you use pulse settings, set the wire feed mode to pulse as well. Otherwise the wire delivery does not match the power delivery. In the wire feed settings you can:

  • Add a feed delay after the ramp up, so the base material is good and hot before the wire starts.
  • Set the pulse duration of the feed to match the process beam. The video uses 130 ms of feed per pulse.
  • Adjust the texture smoothness for a micro-TIG-like bead. Fish scale in basic mode does the same.

Status and warnings

The status page shows the live gas pressure and the temperature of the protective window. The warning page shows the cause of most alarms. With the gas off, the gas warning lights up red. With the interlock open, the interlock warning appears and the laser will not fire. If you see an error in the middle or right column, get support in the THEO Toolbox app.

Parameters Library and saved settings

The built-in parameters are in the Parameters Library. Your saved settings are on the right, under Customize. The buttons at the bottom of that screen let you adjust and overwrite parameters right there, open the wire feed settings, save your changes and load settings you saved earlier.

System information and configuration

System information shows the serial numbers, the machine version, the firmware version and the expiry date. Additional authorization codes go into the authorization code slot.

The configuration page asks for a login code and gives access to the factory thresholds. It is restricted: generally only authorized resellers and THEO staff change those settings.

More THEO MA1 Series tutorials

Questions about your machine? Get support in the Aplikacija THEO Toolbox for iOS and Android.