THEO-tietopankki
THEO MA1 Series -opastus (US) | Kaasuliitännät
Sähkön tapaan myös MA1:n liittäminen kaasunlähteeseen jää sinun vastuullesi. Sovellustiimimme on testannut suuren määrän tarvikkeita, ja alla olevat osat toimivat luotettavimmin yhdysvaltalaisissa konepajoissa. MA1:ssä on 6 mm:n pikaliitin kaasun tulolle. Mukana toimitetaan 10 mm:n kaasuletku ja yksi 10 mm…
Valmistaudu toimitukseen — THEO MA1 Series
Kaikki, minkä pitää olla kunnossa ennen kuin THEO MA1 Series saapuu: lasertyöalue, oma virtapiiri ja pistoke (EU/US), suojakaasu ja paineensäädin, ovikytkin ja savunpoisto.
THEO MA1 -sarja | Käyttöparametrit
Alla on koottu taulukko, joka kattaa kaikki nykyiset MA1‑sarjan käsilaserhitsauslaitteet (MA1‑35, MA1‑45, MA1‑65 ja MA1 ULTRA). Tiedot auttavat laserturvallisuusvastaavaa (LSO) tai turvallisuuskonsulttia suunnittelemaan turvallisen luokan 4 lasertyöympäristön: valitsemaan oikeat suojalasit, määrittämään suojaseinät ja kotelot, järjestämään ilmanvaihdon ja laatimaan kulunvalvonnan menettelyt. Kaikki…
THEO MA1 -sarjan ohjeet | Käsipolttimen suojalasien vaihto
Julkaisupäivä: 4. marraskuuta 2025Muistion numero: TB.MP.11425ARevisio: 1Koskee tuotteita: Kaikki käsikäyttöiset laserjärjestelmät Työkalut: Ohjeet Seuraavat ohjeet opastavat suojalasin (suojaikkunan) vaihdossa kaikissa Theon käsikäyttöisissä laserjärjestelmissä. Ohjeita noudattamalla vähennät fokusointilinssin ja hitsauspään muiden optisten osien likaantumista. Huomio: Järjestä kunnollinen työtila…
THEO MA1 -sarjan ohje (US) | Virransyötön kytkentä
How to wire the power cord of the THEO MA1 Series to its plug for a US single phase 200 to 240 V outlet, terminal by terminal.
THEO MA1 -sarjan ohjeet | Kaasunsäätimet
How to connect the THEO MA1 Series to shielding gas: regulators, tubing and fittings, and a tee to switch between argon and nitrogen.
THEO MA1 -sarjan ohje (US) | Pakkauksen avaus ja käyttöönotto
Unboxing and setup of the THEO MA1 Series, US version: power plug, shielding gas, interlock and loop cable, nozzle, then the wire feeder.
THEO MA1 -sarjan ohje (US) | Lisävarusteet
What is in the THEO MA1 Series welding accessory kit: gas nozzles, wire feeder tips, the liner attachment, and which nozzle to use when.
THEO MA1 -sarjan ohje (EU) | Pakkauksen avaus ja käyttöönotto
Unboxing and setup of the THEO MA1 Series, EU version: activation, gas, interlock and loop cable, welding head, then the wire feeder.
THEO MA1 Series Tutorial | MA1 ULTRA UI Walkthrough
A walk through the THEO MA1 ULTRA interface: the precautions screen, basic and expert mode, the details tab, wire feeder settings and tacking mode.
THEO MA1 Series Tutorial | Setting Proper Defocus
How to set the defocus on the THEO MA1 Series: where to start on steel, how the material changes the setting, and what a wrong setting does.
THEO MA1 Series Tutorial | Torch Handling
How to hold the THEO MA1 Series welding torch: a light grip, the torch parallel to the joint, and why it is not held like a MIG gun.
THEO MA1 Series Tutorial | Proper Posture
How to stand and move when welding with the THEO MA1 Series: guide the torch with your body, stay out of the reflection zone, weld vertical down.
THEO MA1 Series Tutorial | MA1-65 UI Walkthrough
A walk through the THEO MA1-65 interface, the same on the MA1-35 and MA1-45: basic and expert mode, the details menu, tacking and pulse settings.
THEO MA1 Series Tutorial | Proper Wire Alignment
How to align the wire on the THEO MA1 Series: a clean, straight wire, fed through torch and tip, the gas tube straight up and the guide beam on the wire.
THEO Dual Wire Feeder -laajennussarja | Dual Wire Feeder -sarjan käyttöönotto — video-ohje
How to set up the Dual Wire Feeder Kit on the THEO MA1 Series: holder plate, nozzle, splitter box, two wire feeders, dual liner and alignment.