Blog · Handheld Laser Welding

Stop Comparing Watts: Why 2000 W Can Out-Weld 3000 W

November 20, 2026 · 12 min read

Laser weld through a 10.02 mm (0.39 in) thick AISI 304 stainless steel bar, 6.48 mm wide at the crown and 2.68 mm at the root, welded with a THEO MA1 ULTRA. Photo: AK Industry GmbH.
Two laser beams hitting the same steel plate. The sharp 2000 watt beam makes a narrow, deep weld. The blurry 3000 watt beam makes a wide, shallow one.
Same plate, different focus. Schematic, not to scale.

Every quote for a handheld laser welder has one number in bold: watts. 1500. 2000. 3000. Bigger number, deeper weld, done.

Except it doesn’t work that way. Take three handheld laser welders that all say 2000 W on the spec sheet. Their makers list 6 mm, 8 mm and 8.5 mm (0.24, 0.31 and 0.33 in) of stainless steel in a single pass. Now take two that say 3000 W. Both list 8 mm (0.31 in).

Same watts, different depth. More watts, same depth. The 8.5 mm is ours, the THEO MA1 ULTRA at 2000 W. The other machines are named further down.

Watts tell you how much light leaves the laser source. They don’t tell you where it lands. This article is about where it lands.

A laser is a magnifying glass

You ran this experiment as a kid. Sun, magnifying glass, sheet of paper. Hold the glass at the wrong height and you get a bright, warm blob. Hold it at the right height and the paper smokes.

The same sunlight through the same magnifying glass. Held too close, it makes a big warm spot on the paper. Held at the right height, it makes a tiny spot and the paper smokes.
Same sun, same glass. The only thing that changed is the size of the spot.

The sun didn’t get stronger. The same power hit a smaller spot.

Laser welding is that experiment with more at stake. To weld deep, the beam has to boil a narrow channel into the metal, called the keyhole, and hold it open while you move along the joint. What opens a keyhole is concentration: how many watts land on each bit of metal. Spread the same watts over a wider spot and you get a wide, shallow weld pool and a hot part.

Two things make a beam weld deep

Every laser beam narrows to its thinnest point and then spreads again. Two things about that shape decide the weld.

A laser beam narrowing to its thinnest point and spreading again. Spot size is how small the beam gets. Depth of focus is how long it stays small.
A small spot gives the punch. A long depth of focus keeps the punch going down into the joint.

Spot size is how small the beam gets. Smaller spot, more concentration.

Depth of focus is how long the beam stays that small. A long one keeps the concentration up while the beam travels down the keyhole. It also forgives you. Your hand is not a CNC axis, and the torch will sit a little high or a little low all day.

A lens can’t give you both

Here is the catch. Every beam comes with a focus budget. You can spend it on a small spot, or on a long depth of focus. A lens only moves the budget around: squeeze the spot and the beam fans out sooner, stretch the depth of focus and the spot gets fat.

Three beams. A sharp beam has a small spot and a long depth of focus. A blurry beam squeezed to a small spot fans out right away. A blurry beam stretched to a long depth of focus has a fat spot.
Drawn to scale against each other. The blurry beam is about three times harder to focus than the sharp one.

Only a better beam gets you a small spot and a long depth of focus. And how good the beam is gets decided before the lens, in the laser source and the fiber. Nothing after the fiber can improve it.

On a spec sheet the focus budget is called BPP (beam parameter product) or M². For both, lower is sharper. It is the number that decides what your watts can do, and it is missing from most quotes.

Where the third kilowatt usually comes from

The beam is born in the fiber. In a single-mode source with a 20 µm fiber core, the light travels in one clean pattern. That is about as sharp as a beam gets.

Pushing 3000 W through a core that thin, over ten meters (33 ft) of fiber, is hard and expensive. So the common route to 3000 W in a handheld machine is a fatter fiber that carries many patterns of light at once. Look for “fiber core diameter” on the spec sheet. You will often see 20 or 25 µm on a maker’s 1500 W and 2000 W models and 50 µm on the 3000 W model.

Two fiber cores at the same scale. A 20 micron single-mode core carries one clean pattern of light. A 50 micron multi-mode core has about six times the area and carries many patterns at once.
The fat core carries more power. It also delivers a beam that is about three times harder to focus.

That is the trade nobody prints in bold. The third kilowatt was bought with focus.

2000 W against 3000 W: three chances

Take the MA1 ULTRA’s beam and a typical 3000 W beam from a 50 µm fiber. The 3000 W machine gets three chances to spend its focus budget.

Power density at the focus point with the MA1 ULTRA set to 100. 3000 watts through the same torch optics: 24. 3000 watts with depth of focus matched: 51. 3000 watts with the spot squeezed to match: 150, but only at the exact focus point.
Worked example. Concentration means power density, the watts landing on each bit of metal. MA1 ULTRA values as measured on our beam profile; 3000 W values calculated from the middle of the published range for 50 µm sources.

Chance one: through the same optics, the 50 µm beam lands on six times the area. Fifty percent more watts, a quarter of the concentration.

Chance two: match the depth of focus, and the 3000 W beam still delivers about half.

Chance three looks like a win. Squeeze the 3000 W beam down to the same spot and it beats the ULTRA at the focus point. But the budget is spent: its depth of focus is now under a millimeter (0.04 in). Watch what happens when you leave the focus point, which every weld does, because the keyhole is deep and your hand moves.

Line chart of power density against distance from the focus point. The squeezed 3000 watt beam starts at 150 but drops to 70 at 1 millimeter and 27 at 2 millimeters. The MA1 ULTRA starts at 100 and still has 88 at 1 millimeter and 65 at 2 millimeters. Past 0.7 millimeters the 2000 watt beam is the stronger one.
Hold the torch 1 mm (0.04 in) off and the squeezed 3000 W beam has lost about half its concentration. The MA1 ULTRA’s has lost about 12 percent. One of those is a weld you can make by hand, on a real part, at the end of a shift.

For the spec-sheet readers

MA1 ULTRA: spot about 70 µm (0.003 in), depth of focus (Rayleigh length) about 2.75 mm (0.11 in), which works out to a BPP of about 0.45 mm·mrad. Published 3000 W sources with a 50 µm fiber: 1.1 to 2 mm·mrad. We calculated with 1.3.

Power density at the focus point: 52 MW/cm² for the ULTRA; 12, 27 and 78 MW/cm² for the three 3000 W cases.

The shortcut: at the same depth of focus, power density scales with watts divided by BPP. 2000 ÷ 0.45 is about 4,400. 3000 ÷ 1.3 is about 2,300.

Independent research points the same way. TWI, the UK welding institute, ran 4 kW lasers of different beam quality through the same welding trials. At 5 m/min (about 200 in/min) the sharpest beam penetrated 70 percent deeper than the blurriest, at equal power, and the gap widened as travel speed went up (Hilton and Verhaeghe, 2006). Handheld laser welding is fast welding.

What the spec sheets say: six machines, premium to budget

Theory is cheap, so here are the makers’ own numbers. Six handheld laser welders, from the premium end to the budget end, with the laser output power each maker states and the single-pass depth in stainless steel each maker claims. These are not our tests. They are their spec sheets, and ours.

Scatter chart of laser output power against the maker's single-pass depth in stainless steel. At 1200 watts: xTool MetalFab, 5 millimeters. At 2000 watts: DenaliWeld JET 2000, 6 millimeters; IPG LightWELD 2000 XR, 8 millimeters; THEO MA1 ULTRA, 8.5 millimeters. At 3000 watts: DenaliWeld CR3000 and Everlast RedSabre 3000X, both 8 millimeters.
Maker-published figures, read in November 2026. Each maker tests its own way, so read them as claims, ours included.
MachineLaser outputStainless, one passCoolingSupplyFiber core, beam quality
THEO MA1 ULTRA2000 Wup to 8.5 mm (0.33 in)Air200–240 V single-phase20 µm, single-mode
IPG LightWELD 2000 XR2000 Wup to 8 mm (0.313 in)Air220 V single-phasenot published
DenaliWeld JET 20002000 W0.5–6 mm (0.02–0.24 in) recommended¹Air220 Vnot published
DenaliWeld CR30003000 W0.5–8 mm (0.02–0.31 in) recommended¹Water380 V three-phasenot published
Everlast RedSabre 3000X3000 Wup to 8 mm (0.31 in)Refrigerated240/480 V three-phase or 240 V single-phase50 µm, M² ≤ 3
xTool MetalFab 1200 W1200 Wup to 5 mm (0.20 in)Airnot statednot published
¹ Series figure from the user manual. Maker-published figures, read in November 2026. Sources are listed at the end of this article.

Four things stand out.

Watts don’t sort the list. Three machines share 2000 W and claim 6, 8 and 8.5 mm (0.24, 0.31 and 0.33 in). Both 3000 W machines claim 8 mm (0.31 in). If watts decided depth, the 3000 W machines would be at 12 mm (0.47 in).

The premium end agrees with itself. IPG gets 8 mm (0.31 in) out of 2000 W with air cooling. Different brand, same lesson: a well-focused 2000 W does the work of a 3000 W.

The third kilowatt comes with luggage. Everything up to 2000 W on this list is air-cooled. Both 3000 W machines bring liquid cooling, and one needs a three-phase supply.

Almost nobody prints the number that matters. Only two of the six publish a fiber core or a beam quality figure. Everlast deserves credit for doing it, and its sheet tells the whole story of this article in one row: 25 µm fiber and M² ≤ 1.2 on the 1500 W model, 50 µm and M² ≤ 3 on the 3000 W model.

And the small machine? xTool lists 5 mm (0.20 in) from 1200 W. A modest laser with decent focus goes a long way. It just stops at 5 mm.

Spec sheets are claims. Shops are proof. At AK Industry in Germany, this butt joint in 10 mm (0.39 in) AISI 304 stainless steel was welded through with an MA1 ULTRA and the Dual Wire Kit. No gap, no edge preparation. That is more than the 8.5 mm (0.33 in) on our own spec sheet.

A 10 mm thick bar of AISI 304 stainless steel with a laser weld through its full thickness. The weld is 6.48 mm wide at the top and 2.68 mm at the root. I-butt joint, no gap, no edge preparation, welded with a THEO MA1 ULTRA including the Dual Wire Kit.
Polished cross-section of the same kind of weld under a microscope. The plate is 9.87 mm thick and the weld runs from a 6.83 mm wide crown to a 2.89 mm wide root bead on the far side.
10 mm (0.39 in) AISI 304, I-butt joint, no gap, no edge preparation, MA1 ULTRA with Dual Wire Kit. Top: the welded bar. Bottom: the polished cross-section, 9.87 mm (0.39 in) thick, fused from crown to root. Photos: AK Industry GmbH, Germany.

How we build for depth

We start from the weld and work back to the watts.

The MA1 ULTRA runs a single-mode Maxphotonics laser source with a 20 µm fiber core. That is where the sharp beam comes from, and everything after it is about not wasting it.

The optical path is short. The fiber connects straight to the torch, with no extra connector lens in between. Every junction in the path is a place to lose focus, so we left them out.

The focus is set for a hand, not a robot: a small spot with enough depth of focus to keep the concentration up from the surface to the root, and to keep it there when the torch moves.

Width comes from wobble. The torch swings the beam across the joint, up to 4 mm (0.16 in) wide. The fine beam does the digging and the wobble does the bridging.

Top view of a joint. On the left a fine beam zigzags across the seam to make a weld up to 4 millimeters wide. On the right a wide beam covers the same width in one stroke but has less depth.
Looking down on the joint. Two ways to make a seam the same width.

Fewer watts also means less heat to get rid of. The MA1 ULTRA is air-cooled and runs on single-phase 200–240 V.

And it is why you won’t find watts in our model names. 35, 45 and 65 are millimeters, not kilowatts. We name the machine after what it does to your part.

The MA1 range. MA1-35: up to 3.5 millimeters or 0.14 inches, 800 watts. MA1-45: up to 4.5 millimeters or 0.18 inches, 1200 watts. MA1-65: up to 6.5 millimeters or 0.26 inches, 1500 watts. MA1 ULTRA: up to 8.5 millimeters or 0.33 inches, 2000 watts.
Up to, in stainless steel, in one pass.

When more watts do win

More watts are not a trick. They help in three cases.

At the same sharpness, more power is deeper and faster. If a quote shows 3000 W and a single-mode beam at the torch, take it seriously.

Filler-heavy work is energy bookkeeping. Wide gaps and big fillets need a lot of wire melted, and melting wire takes watts wherever they land.

And focus has a ceiling. Past a certain point a finer beam adds no more depth, and a needle-fine beam on a poorly fitted joint is unforgiving. That is what the wobble is for.

So watts matter. They are just the second question.

Six questions that beat “how many watts?”

Take these to any demo, ours included.

  1. How deep does it weld my material in one pass? Show me the cross-section.
  2. What is the fiber core diameter, and is the source single-mode or multi-mode?
  3. What is the beam quality (BPP or M²) at the torch, not at the laser source?
  4. What are the spot size and the depth of focus?
  5. How much power arrives at the torch after ten minutes of welding?
  6. What does the machine need from my shop: supply, cooling, floor space?

A seller who knows the machine answers all six without leaving the room.

Sources

  • Maker-published specifications, read on 20 November 2026: THEO, MA1 Series page (theo.inc). IPG Photonics, LightWELD 2000 XR datasheet and capabilities page (ipgphotonics.com). DenaliWeld, JET series and CR water-cooled series user manuals (denaliweld.com). Everlast, RedSabre laser welder specification sheet, rev. 3/29/2024 (everlastgenerators.com). xTool, MetalFab laser welder product page (xtool.com).
  • P. Hilton and G. Verhaeghe, TWI Ltd, “Selecting the source”, Industrial Laser Solutions, June 2006.
  • Beam quality of 3000 W fiber laser sources with a 50 µm fiber: manufacturer specification sheets, 1.1 to 2 mm·mrad.
  • Weld sample and cross-section: AK Industry GmbH, Germany.

Bring your thickest part

Don’t take our word for it, and don’t take a spec sheet’s either. Bring the joint you actually weld and look at the cross-section.
BOOK A DEMO

Frequently Asked Questions

Only if the beam is equally sharp. Many 3000 W handheld machines use a 50 µm multi-mode fiber, which spreads the power over a larger spot or shortens the depth of focus. A 2000 W single-mode beam can put more concentrated power into the joint.
How concentrated the power is inside the keyhole. That depends on laser output power, spot size and how well the beam holds its focus over depth, plus travel speed and material.
The beam parameter product. It describes how well a beam can be focused. Lower is better, and no lens after the fiber can improve it. M² describes the same thing.
Up to 8.5 mm (0.33 in) in stainless steel, carbon steel and galvanized sheet in one pass, and up to 6.5 mm (0.26 in) in aluminum.

Ready to see a THEO laser welder in action?

Book a demo at a partner near you or get a quote.
Get a quote