Every quote for a handheld laser welder has one number in bold: watts. 1500. 2000. 3000. Bigger number, deeper weld, done.
Except it doesn’t work that way. Take three handheld laser welders that all say 2000 W on the spec sheet. Their makers list 6 mm, 8 mm and 8.5 mm (0.24, 0.31 and 0.33 in) of stainless steel in a single pass. Now take two that say 3000 W. Both list 8 mm (0.31 in).
Same watts, different depth. More watts, same depth. The 8.5 mm is ours, the THEO MA1 ULTRA at 2000 W. The other machines are named further down.
Watts tell you how much light leaves the laser source. They don’t tell you where it lands. This article is about where it lands.
A laser is a magnifying glass
You ran this experiment as a kid. Sun, magnifying glass, sheet of paper. Hold the glass at the wrong height and you get a bright, warm blob. Hold it at the right height and the paper smokes.
The sun didn’t get stronger. The same power hit a smaller spot.
Laser welding is that experiment with more at stake. To weld deep, the beam has to boil a narrow channel into the metal, called the keyhole, and hold it open while you move along the joint. What opens a keyhole is concentration: how many watts land on each bit of metal. Spread the same watts over a wider spot and you get a wide, shallow weld pool and a hot part.
Two things make a beam weld deep
Every laser beam narrows to its thinnest point and then spreads again. Two things about that shape decide the weld.
Spot size is how small the beam gets. Smaller spot, more concentration.
Depth of focus is how long the beam stays that small. A long one keeps the concentration up while the beam travels down the keyhole. It also forgives you. Your hand is not a CNC axis, and the torch will sit a little high or a little low all day.
A lens can’t give you both
Here is the catch. Every beam comes with a focus budget. You can spend it on a small spot, or on a long depth of focus. A lens only moves the budget around: squeeze the spot and the beam fans out sooner, stretch the depth of focus and the spot gets fat.
Only a better beam gets you a small spot and a long depth of focus. And how good the beam is gets decided before the lens, in the laser source and the fiber. Nothing after the fiber can improve it.
On a spec sheet the focus budget is called BPP (beam parameter product) or M². For both, lower is sharper. It is the number that decides what your watts can do, and it is missing from most quotes.
Where the third kilowatt usually comes from
The beam is born in the fiber. In a single-mode source with a 20 µm fiber core, the light travels in one clean pattern. That is about as sharp as a beam gets.
Pushing 3000 W through a core that thin, over ten meters (33 ft) of fiber, is hard and expensive. So the common route to 3000 W in a handheld machine is a fatter fiber that carries many patterns of light at once. Look for “fiber core diameter” on the spec sheet. You will often see 20 or 25 µm on a maker’s 1500 W and 2000 W models and 50 µm on the 3000 W model.
That is the trade nobody prints in bold. The third kilowatt was bought with focus.
2000 W against 3000 W: three chances
Take the MA1 ULTRA’s beam and a typical 3000 W beam from a 50 µm fiber. The 3000 W machine gets three chances to spend its focus budget.
Chance one: through the same optics, the 50 µm beam lands on six times the area. Fifty percent more watts, a quarter of the concentration.
Chance two: match the depth of focus, and the 3000 W beam still delivers about half.
Chance three looks like a win. Squeeze the 3000 W beam down to the same spot and it beats the ULTRA at the focus point. But the budget is spent: its depth of focus is now under a millimeter (0.04 in). Watch what happens when you leave the focus point, which every weld does, because the keyhole is deep and your hand moves.
For the spec-sheet readers
MA1 ULTRA: spot about 70 µm (0.003 in), depth of focus (Rayleigh length) about 2.75 mm (0.11 in), which works out to a BPP of about 0.45 mm·mrad. Published 3000 W sources with a 50 µm fiber: 1.1 to 2 mm·mrad. We calculated with 1.3.
Power density at the focus point: 52 MW/cm² for the ULTRA; 12, 27 and 78 MW/cm² for the three 3000 W cases.
The shortcut: at the same depth of focus, power density scales with watts divided by BPP. 2000 ÷ 0.45 is about 4,400. 3000 ÷ 1.3 is about 2,300.
Independent research points the same way. TWI, the UK welding institute, ran 4 kW lasers of different beam quality through the same welding trials. At 5 m/min (about 200 in/min) the sharpest beam penetrated 70 percent deeper than the blurriest, at equal power, and the gap widened as travel speed went up (Hilton and Verhaeghe, 2006). Handheld laser welding is fast welding.
What the spec sheets say: six machines, premium to budget
Theory is cheap, so here are the makers’ own numbers. Six handheld laser welders, from the premium end to the budget end, with the laser output power each maker states and the single-pass depth in stainless steel each maker claims. These are not our tests. They are their spec sheets, and ours.
| Machine | Laser output | Stainless, one pass | Cooling | Supply | Fiber core, beam quality |
|---|---|---|---|---|---|
| THEO MA1 ULTRA | 2000 W | up to 8.5 mm (0.33 in) | Air | 200–240 V single-phase | 20 µm, single-mode |
| IPG LightWELD 2000 XR | 2000 W | up to 8 mm (0.313 in) | Air | 220 V single-phase | not published |
| DenaliWeld JET 2000 | 2000 W | 0.5–6 mm (0.02–0.24 in) recommended¹ | Air | 220 V | not published |
| DenaliWeld CR3000 | 3000 W | 0.5–8 mm (0.02–0.31 in) recommended¹ | Water | 380 V three-phase | not published |
| Everlast RedSabre 3000X | 3000 W | up to 8 mm (0.31 in) | Refrigerated | 240/480 V three-phase or 240 V single-phase | 50 µm, M² ≤ 3 |
| xTool MetalFab 1200 W | 1200 W | up to 5 mm (0.20 in) | Air | not stated | not published |
Four things stand out.
Watts don’t sort the list. Three machines share 2000 W and claim 6, 8 and 8.5 mm (0.24, 0.31 and 0.33 in). Both 3000 W machines claim 8 mm (0.31 in). If watts decided depth, the 3000 W machines would be at 12 mm (0.47 in).
The premium end agrees with itself. IPG gets 8 mm (0.31 in) out of 2000 W with air cooling. Different brand, same lesson: a well-focused 2000 W does the work of a 3000 W.
The third kilowatt comes with luggage. Everything up to 2000 W on this list is air-cooled. Both 3000 W machines bring liquid cooling, and one needs a three-phase supply.
Almost nobody prints the number that matters. Only two of the six publish a fiber core or a beam quality figure. Everlast deserves credit for doing it, and its sheet tells the whole story of this article in one row: 25 µm fiber and M² ≤ 1.2 on the 1500 W model, 50 µm and M² ≤ 3 on the 3000 W model.
And the small machine? xTool lists 5 mm (0.20 in) from 1200 W. A modest laser with decent focus goes a long way. It just stops at 5 mm.
Spec sheets are claims. Shops are proof. At AK Industry in Germany, this butt joint in 10 mm (0.39 in) AISI 304 stainless steel was welded through with an MA1 ULTRA and the Dual Wire Kit. No gap, no edge preparation. That is more than the 8.5 mm (0.33 in) on our own spec sheet.
How we build for depth
We start from the weld and work back to the watts.
The MA1 ULTRA runs a single-mode Maxphotonics laser source with a 20 µm fiber core. That is where the sharp beam comes from, and everything after it is about not wasting it.
The optical path is short. The fiber connects straight to the torch, with no extra connector lens in between. Every junction in the path is a place to lose focus, so we left them out.
The focus is set for a hand, not a robot: a small spot with enough depth of focus to keep the concentration up from the surface to the root, and to keep it there when the torch moves.
Width comes from wobble. The torch swings the beam across the joint, up to 4 mm (0.16 in) wide. The fine beam does the digging and the wobble does the bridging.
Fewer watts also means less heat to get rid of. The MA1 ULTRA is air-cooled and runs on single-phase 200–240 V.
And it is why you won’t find watts in our model names. 35, 45 and 65 are millimeters, not kilowatts. We name the machine after what it does to your part.
When more watts do win
More watts are not a trick. They help in three cases.
At the same sharpness, more power is deeper and faster. If a quote shows 3000 W and a single-mode beam at the torch, take it seriously.
Filler-heavy work is energy bookkeeping. Wide gaps and big fillets need a lot of wire melted, and melting wire takes watts wherever they land.
And focus has a ceiling. Past a certain point a finer beam adds no more depth, and a needle-fine beam on a poorly fitted joint is unforgiving. That is what the wobble is for.
So watts matter. They are just the second question.
Six questions that beat “how many watts?”
Take these to any demo, ours included.
- How deep does it weld my material in one pass? Show me the cross-section.
- What is the fiber core diameter, and is the source single-mode or multi-mode?
- What is the beam quality (BPP or M²) at the torch, not at the laser source?
- What are the spot size and the depth of focus?
- How much power arrives at the torch after ten minutes of welding?
- What does the machine need from my shop: supply, cooling, floor space?
A seller who knows the machine answers all six without leaving the room.
Sources
- Maker-published specifications, read on 20 November 2026: THEO, MA1 Series page (theo.inc). IPG Photonics, LightWELD 2000 XR datasheet and capabilities page (ipgphotonics.com). DenaliWeld, JET series and CR water-cooled series user manuals (denaliweld.com). Everlast, RedSabre laser welder specification sheet, rev. 3/29/2024 (everlastgenerators.com). xTool, MetalFab laser welder product page (xtool.com).
- P. Hilton and G. Verhaeghe, TWI Ltd, “Selecting the source”, Industrial Laser Solutions, June 2006.
- Beam quality of 3000 W fiber laser sources with a 50 µm fiber: manufacturer specification sheets, 1.1 to 2 mm·mrad.
- Weld sample and cross-section: AK Industry GmbH, Germany.