Отваря се в нов раздел
База знания на THEO · Уроци

Урок за THEO MA1 Series (САЩ) | Разопаковане и настройка

This video shows how to unbox a THEO MA1 handheld laser welder and the THEO T1 Wire Feeder in the US and get them ready for the first weld: the power plug, the first start and activation, shielding gas, the gas and interlock alarms, the workpiece clamp, the welding nozzle, the protective window and the wire feed all the way to the torch.

What is in the MA1 box

The packing list sits on top and names everything in the box. Under it you find:

  • Three pairs of laser safety glasses.
  • Earplugs and dust masks for the welding environment.
  • The consumables box: welding nozzles, wire feed nozzles, the adapter that connects the wire feed liner to the welding torch, and spare protective windows for the torch.
  • The machine key, in the foam insert under the earplugs.

Take out the foam insert and lift the MA1 onto a table.

Fit the power plug

The MA1 runs on 200 to 240 V AC, single phase. In the video the power cord gets an L6-30P plug, wired with a Phillips screwdriver. Fit the plug your outlet needs. The Power Connection (US) video shows the wiring step by step. Plug and circuit requirements are also in the Get Ready for Delivery guide.

Switch on and accept the safety notices

  1. Plug the MA1 into a 200 to 240 V single-phase outlet.
  2. Insert the key and turn it on, then switch on the power switch on the back panel.
  3. Read each safety notice and press Next. On the last screen, tick the box at the bottom left to confirm you have read and accepted all of them.

Enter the authorization code

If the screen says the license has expired, contact your distributor for your login code and authorization code. Open the System Information page, tap the Authorization box and enter the code. You need to do this before you can start welding.

Find out which alarms are active

A red warning light and a buzzer mean an alarm is active. To see which one, open Expert Mode and the Warning tab. A new machine usually shows two:

  • Gas alarm: the MA1 needs a gas supply of at least 58 kPa.
  • Interlock alarm: the DB25 cable is not connected to the back panel yet.

Connect the shielding gas

The video uses two regulators, one on a nitrogen cylinder and one on an argon cylinder. Argon is the better choice for aluminum and aluminum alloys, nitrogen for most kinds of steel. A T-fitting joins both lines to the single gas inlet on the MA1, so you can switch gases without re-plumbing.

  1. Switch the MA1 off and fit the regulator to the cylinder.
  2. Push the gas hose into the gas inlet on the back panel and give it a short tug to check it is secure.
  3. Open the cylinder and the regulator.
  4. Switch the MA1 on, open Expert Mode and the Status tab, and check the gas pressure. The video shows 317 kPa, well above the 58 kPa minimum, and the gas alarm is gone.

Fittings, tubing sizes and flow are in the Gas Regulators video and the MA1 Gas Plumbing Guide (US).

Connect the interlock and the workpiece clamp

Plug the male end of the DB25 cable into the female External Control input on the back panel. The interlock alarm clears.

Then connect the workpiece clamp. Its cable plugs into the socket on the front of the MA1, and the clamp goes onto your metal welding table. This closes a safety loop that tells the MA1 the welding torch is in contact with the table or the workpiece. It is an extra safety feature: the laser does not fire without that contact.

Fit and align the welding nozzle

The MA1 ships without a welding nozzle on the torch. The welding nozzles are in the consumables pack. The video uses welding nozzle B, for wire welding with 1.2 mm or 1.6 mm wire.

  1. Screw the nozzle onto the end of the connection pipe.
  2. The first time, the nozzle may not sit straight. Loosen the collet and turn the nozzle until the groove points straight down.
  3. Tighten the collet again.

Check the protective window

If you weld every day, this is your most important maintenance point.

  1. Loosen the nut and pull out the protective window holder.
  2. Cover the opening with tape right away, so no dirt gets into the optics.
  3. Wear nitrile finger cots or nitrile gloves, so you leave no fingerprints on the window.
  4. Hold the window up to a light and look for dust, dirt, debris or burn spots.
  5. If you find any, fit a new window from the kit that came with the machine.
  6. Remove the tape, slide the holder back in and tighten the nut.

Unbox the T1 Wire Feeder

The THEO T1 Wire Feeder has its own packing list on top. Lift it out with two people. Under the foam insert you find the liner, the keys for the wire feeder and the drive rolls.

Connect the communication cable between the T1 and the MA1: line up the red dot on the plug with the red dot on the socket, pull back the sleeve and push the plug in.

Load the wire spool and drive rolls

Open the side panel. Remove the end cap and, for a large spool, the bracket that holds smaller spools. Then match the drive rolls to the wire. The T1 ships with 1.0 mm V-groove drive rolls. The video loads a 7.3 kg (16 lb) spool of ER5356 aluminum wire, 1.2 mm (0.045 in), so it swaps them for 1.2 mm U-groove drive rolls.

  1. Mount the spool.
  2. Feed the wire through the drive roll mechanism, with the wire sitting in the grooves of the drive rolls.
  3. Push it on until it comes out of the wire feeder outlet.
  4. Close the tension arms.

Feed the wire through the liner

  1. With the MA1 on, switch on the T1. When the power button lights up red, it has power.
  2. Slide the liner over the wire and push it into the outlet until it clicks.
  3. Press and hold the feed button. After two seconds you can let go and the wire keeps feeding.
  4. When the wire comes out of the far end of the liner, press the button again to stop.

Attach the liner to the welding torch

From the consumables pack you need the wire feed bracket, the tool for its screw and the wire feed nozzle for your wire diameter: 1.2 mm (0.045 in).

  1. Slide the bracket over the wire and push it onto the liner until it clicks.
  2. Thread the wire feed nozzle over the wire and screw it onto the bracket. If too little wire sticks out, feed a little more.
  3. Loosen the screw on the adapter and slide the adapter onto the connection pipe of the welding torch.
  4. Check that the groove of the welding nozzle points straight down.
  5. Lay the wire in the groove. It should come out straight, in line with the groove, without much bend.
  6. Tighten the screw.

The MA1 is now set up for wire welding. How to fine-tune the wire is in Proper Wire Alignment.

More THEO MA1 Series tutorials

Questions about your machine? Get support in the Приложението THEO Toolbox for iOS and Android.