Уроци
Подгответе се за доставката — THEO MA1 Series
Всичко, което трябва да е готово, преди да пристигне вашата THEO MA1 Series: зона за лазерна безопасност, отделна електрическа верига и щепсел (EU/US), защитен газ и регулатор, блокировка на вратата, аспирация на дима.
Урок за THEO MA1 Series (САЩ) | Разопаковане и настройка
Unboxing and setup of the THEO MA1 Series, US version: power plug, shielding gas, interlock and loop cable, nozzle, then the wire feeder.
Урок за THEO MA1 Series (ЕС) | Разопаковане и настройка
Unboxing and setup of the THEO MA1 Series, EU version: activation, gas, interlock and loop cable, welding head, then the wire feeder.
Урок за THEO MA1 Series (САЩ) | Свързване към захранването
How to wire the power cord of the THEO MA1 Series to its plug for a US single phase 200 to 240 V outlet, terminal by terminal.
Уроци за THEO MA1 Series | Газови регулатори
How to connect the THEO MA1 Series to shielding gas: regulators, tubing and fittings, and a tee to switch between argon and nitrogen.
Урок за THEO MA1 Series (САЩ) | Аксесоари
What is in the THEO MA1 Series welding accessory kit: gas nozzles, wire feeder tips, the liner attachment, and which nozzle to use when.
Урок за THEO MA1 Series (US) | Свързване на газовата инсталация
Както при електрозахранването, свързването на MA1 към Вашия източник на газ е Ваша задача. Нашият екип по приложенията изпробва много компоненти и частите по-долу работят най-надеждно в американските работилници. MA1 има вход за газ 6 mm с бързо свързване. Доставя се с маркуч за газ 10 mm и един 10 mm…
Уроци за THEO MA1 Series | Смяна на плъзгача на защитния капак на ръчната горелка
Дата на издаване: 4 ноем. 2025 г.Номер на документа: TB.MP.11425AРевизия: 1Засегнати продукти: Всички ръчни лазерни системи Инструменти: Инструкции Следващите инструкции насочват при смяната на защитното стъкло (прозорче) във всички ръчни лазерни системи на THEO. Те намаляват замърсяването на фокусиращата леща и на всички останали оптични компоненти в горелката. Забележка: Осигурете подходящо работно място…
THEO MA1 Series Tutorial | MA1 ULTRA UI Walkthrough
A walk through the THEO MA1 ULTRA interface: the precautions screen, basic and expert mode, the details tab, wire feeder settings and tacking mode.
THEO MA1 Series Tutorial | Setting Proper Defocus
How to set the defocus on the THEO MA1 Series: where to start on steel, how the material changes the setting, and what a wrong setting does.
THEO MA1 Series Tutorial | Torch Handling
How to hold the THEO MA1 Series welding torch: a light grip, the torch parallel to the joint, and why it is not held like a MIG gun.
THEO MA1 Series Tutorial | Proper Posture
How to stand and move when welding with the THEO MA1 Series: guide the torch with your body, stay out of the reflection zone, weld vertical down.
THEO MA1 Series Tutorial | MA1-65 UI Walkthrough
A walk through the THEO MA1-65 interface, the same on the MA1-35 and MA1-45: basic and expert mode, the details menu, tacking and pulse settings.
THEO MA1 Series Tutorial | Proper Wire Alignment
How to align the wire on the THEO MA1 Series: a clean, straight wire, fed through torch and tip, the gas tube straight up and the guide beam on the wire.