Tutoriels
Préparez la livraison — THEO MA1 Series
Tout ce qui doit être en place avant l'arrivée de votre THEO MA1 Series : zone de sécurité laser, circuit électrique dédié et prise (UE/US), gaz de protection et détendeur, verrouillage de porte, aspiration des fumées.
Tutoriel THEO MA1 Series (US) | Déballage et installation
Unboxing and setup of the THEO MA1 Series, US version: power plug, shielding gas, interlock and loop cable, nozzle, then the wire feeder.
Tutoriel THEO MA1 Series (UE) | Déballage et installation
Unboxing and setup of the THEO MA1 Series, EU version: activation, gas, interlock and loop cable, welding head, then the wire feeder.
Tutoriel THEO MA1 Series (US) | Raccordement électrique
How to wire the power cord of the THEO MA1 Series to its plug for a US single phase 200 to 240 V outlet, terminal by terminal.
Tutoriels THEO MA1 Series | Détendeurs de gaz
How to connect the THEO MA1 Series to shielding gas: regulators, tubing and fittings, and a tee to switch between argon and nitrogen.
Tutoriel THEO MA1 Series (US) | Accessoires
What is in the THEO MA1 Series welding accessory kit: gas nozzles, wire feeder tips, the liner attachment, and which nozzle to use when.
Tutoriel THEO MA1 Series (US) | Guide de raccordement du gaz
Comme pour l'électricité, le raccordement du MA1 à votre source de gaz est à votre charge. Notre équipe applications a testé beaucoup de matériel, et les pièces ci-dessous sont celles qui donnent les résultats les plus constants dans les ateliers américains. Le MA1 a une entrée de gaz à raccord instantané de 6 mm. Il est livré avec un tuyau de gaz de 10 mm et un 10 mm…
Tutoriels THEO MA1 Series | Remplacement des lamelles de protection de la torche portative
Date d'émission : 4 novembre 2025Numéro de note : TB.MP.11425ARévision : 1Produits concernés : tous les systèmes laser portables Outils : Instructions Les instructions suivantes guident le remplacement du verre de protection coulissant (fenêtre) sur tous les systèmes laser portables THEO. Elles limitent la contamination de la lentille de focalisation et de tous les autres composants optiques de la torche. Remarque : aménagez un poste de travail adapté…
THEO MA1 Series Tutorial | MA1 ULTRA UI Walkthrough
A walk through the THEO MA1 ULTRA interface: the precautions screen, basic and expert mode, the details tab, wire feeder settings and tacking mode.
THEO MA1 Series Tutorial | Setting Proper Defocus
How to set the defocus on the THEO MA1 Series: where to start on steel, how the material changes the setting, and what a wrong setting does.
THEO MA1 Series Tutorial | Torch Handling
How to hold the THEO MA1 Series welding torch: a light grip, the torch parallel to the joint, and why it is not held like a MIG gun.
THEO MA1 Series Tutorial | Proper Posture
How to stand and move when welding with the THEO MA1 Series: guide the torch with your body, stay out of the reflection zone, weld vertical down.
THEO MA1 Series Tutorial | MA1-65 UI Walkthrough
A walk through the THEO MA1-65 interface, the same on the MA1-35 and MA1-45: basic and expert mode, the details menu, tacking and pulse settings.
THEO MA1 Series Tutorial | Proper Wire Alignment
How to align the wire on the THEO MA1 Series: a clean, straight wire, fed through torch and tip, the gas tube straight up and the guide beam on the wire.